Drying laundry indoors adds a substantial burst of moisture to the air, but the right room, ventilation routine and a simple humidity log can greatly reduce window condensation, damp and mould risk. This UK-focused plan explains how to choose a drying space, estimate the likely impact, compare ventilation options and decide when your current approach needs changing.
Overview
Indoor clothes drying is often unavoidable in winter, in flats without outdoor space or during wet weather. The problem is not the washing itself; it is the water released as clothes dry. If that moisture remains in a cool room, it can settle on windows, external walls and hidden surfaces. Repeated condensation can contribute to musty smells, peeling finishes and mould growth.
The most reliable approach combines four actions:
- Dry laundry in one controllable room rather than spreading it around the home.
- Use the room with the best extraction, warmth and separation from bedrooms or living areas.
- Increase ventilation during and after the drying period.
- Measure relative humidity so decisions are based on a pattern rather than a single fogged window.
A small digital hygrometer is useful for this purpose. As a practical working guide, many households aim to keep indoor relative humidity broadly around 40–60%, while recognising that readings vary with temperature, occupancy and the measuring device. A persistent high reading, visible condensation or recurring mould warrants investigation rather than simply opening a window for a few minutes.
For a wider assessment of humidity, carbon dioxide and particles, see how to measure indoor air quality at home. If you rent, record defects such as failed fans, blocked vents or penetrating damp and use the rental property ventilation checklist when reporting them.
How to estimate
You do not need to calculate the exact mass of water in every load to compare drying methods. Use a repeatable before-and-after process instead.
- Measure the room before drying. Record temperature and relative humidity after the door and windows have been in their normal position for at least 15 minutes.
- Record the laundry load. Note whether it is a small, medium or large load, whether clothes came from a high-spin cycle and how densely they are placed on the airer.
- Measure during drying. Take a reading after one or two hours, then again when the clothes are dry. Note whether the extractor, MVHR boost or PIV system was operating.
- Measure after ventilation. Record the reading 30–60 minutes after drying, and check windows, corners and external walls for condensation.
- Repeat the test. Compare at least three similar laundry cycles before deciding whether a change has worked.
A simple result can be expressed as:
Humidity rise = highest drying-cycle reading minus starting reading
For example, if a room starts at 52% relative humidity and reaches 68%, the rise is 16 percentage points. If it returns close to its starting level after ventilation and does not produce visible condensation, the room may be coping. If the reading remains high for hours or rises further with each load, reduce the moisture load or improve extraction.
Do not treat the calculation as a medical, building-survey or mould diagnosis. It is a household comparison tool that helps you test whether a particular room and ventilation routine are effective.
Inputs and assumptions
Choose the best room
The best room is usually one that has a working extractor or effective mechanical ventilation, a door that can be closed and enough space to separate garments. A bathroom may be suitable if it has effective extraction and the airer does not obstruct the fan or create a safety issue. A kitchen is less suitable when cooking at the same time, because it already contains moisture and odours.
A heated utility room with direct extraction can work well. Avoid placing wet clothes in bedrooms, especially where condensation already forms, or directly against external walls and furniture. Keep the airer away from radiators unless the manufacturer permits the arrangement and airflow is not blocked; covering a radiator can reduce heat circulation and may increase drying time.
Improve the laundry before it enters the room
Use the highest practical spin speed that is suitable for the fabric. Remove clothes promptly, shake them out and leave space between garments. A crowded airer slows drying and releases moisture for longer. If possible, dry smaller loads rather than filling several airers at once.
Use ventilation deliberately
With an extractor fan, close the room door while drying and run the fan during the cycle and afterwards, following the appliance instructions. A timer or humidity-controlled fan can make this easier, but a fan should discharge outdoors rather than into a loft, wall cavity or another room.
With MVHR, use the system’s normal setting and its temporary boost function when appropriate. Keep supply and extract grilles clean and unobstructed. Avoid switching the whole system off because of a single laundry cycle; instead, check the manufacturer’s guidance and arrange maintenance if airflow seems weak. For system comparisons, read MVHR vs PIV vs extractor fans.
PIV introduces filtered air and can help dilute moisture across the home, but it is not a substitute for local extraction where moisture is produced. Keep trickle vents and other designed air paths open unless a professional has advised otherwise. More information about installation and running-cost assumptions is available in the PIV cost guide.
Consider a dehumidifier carefully
A dehumidifier can be useful when outdoor conditions make window ventilation impractical or when extraction is limited. Select a model appropriate for the room, keep doors and windows closed while it operates and empty or drain it safely. A dehumidifier uses electricity, so compare its running time with the cost and effectiveness of improving a faulty extractor or whole-house ventilation system. It should not conceal penetrating damp, leaks or a ventilation defect.
Worked examples
Example 1: Bathroom with a working extractor
A household places one airer in a bathroom, keeps the door closed, runs the extractor during drying and records 50% humidity before, 67% at the peak and 54% after an hour of extraction. There is light misting on the mirror but no wet external wall. The 17-point rise is significant, yet the room returns close to its starting level. The next test should use more spacing between garments and confirm that the fan grille is clean and the external outlet is clear.
Example 2: Living room with no local extraction
An airer is placed in the living room because it is warm. The room starts at 55%, reaches 72% and remains at 68% two hours later. Condensation appears on the window and the air feels stale. Opening the window briefly gives only temporary relief. In this case, move the airer to a room with controllable extraction if possible. If no suitable room exists, compare a properly used dehumidifier with improving mechanical extraction. Repeated high readings should prompt a ventilation assessment rather than continued reliance on window opening.
Example 3: Home with MVHR
A home with MVHR starts at 48%, reaches 61% during a medium load and returns to 50% after the system’s temporary boost period. No visible condensation develops. This suggests the system and room arrangement are coping with that load. If later readings rise, check filters, grilles, boost settings and whether the laundry is being dried in a room served by extract ventilation.
When to recalculate
Repeat the log when the conditions change, not just once a year. Recalculate after replacing windows, adding insulation, installing or repairing an extractor, changing an MVHR filter, buying a dehumidifier or moving the drying rack to another room. New windows can reduce background air leakage, so review the ventilation checklist after window replacement.
Run a fresh comparison at the start of autumn and during a cold spell, when surfaces are cooler and laundry may stay indoors for longer. Recheck after a change in household size, washing frequency or occupancy. Also review the plan if condensation becomes persistent, mould returns after cleaning, paint starts to blister or a musty smell remains.
Use this action sequence:
- Choose one drying room and place the hygrometer at breathing height, away from the airer and direct airflow.
- Log starting, peak and post-drying humidity for three comparable loads.
- Check the fan, vents, filters, door position and airer spacing.
- Change one variable at a time, then repeat the log.
- Arrange professional advice if ventilation is noisy or weak, moisture remains high, or damp appears unrelated to laundry.
For seasonal checks, use the home ventilation maintenance checklist. A measured routine will not eliminate every condensation problem, but it can show whether indoor laundry is the main moisture source and which ventilation improvement is most proportionate.