MVHR vs PIV vs Extractor Fans: Which Ventilation System Is Best for Your UK Home?
MVHRPIVextractor fansventilation comparisonhome ventilation costsbuyer guide

MVHR vs PIV vs Extractor Fans: Which Ventilation System Is Best for Your UK Home?

AAirvent Editorial Team
2026-11-10
6 min read

Compare MVHR, PIV and extractor fans using practical cost, installation, maintenance and quote-checking guidance for UK homes.

Choosing between MVHR, PIV and extractor fans depends on your home’s layout, airtightness, moisture problems, budget and willingness to maintain the system. This guide compares the three options, explains how to estimate the full cost of ownership and gives you a repeatable way to assess quotations without relying on headline installation prices.

Overview

MVHR, PIV and extractor fans solve different ventilation problems. There is no single best ventilation system for every UK house.

Mechanical ventilation with heat recovery (MVHR) is a whole-house system. It continuously extracts stale, moist air from rooms such as kitchens, bathrooms and utility areas, while supplying filtered outdoor air to living rooms and bedrooms. A heat exchanger transfers warmth from the outgoing air to the incoming air. MVHR is generally most effective where the building is reasonably airtight and there is space for correctly designed ductwork.

Positive input ventilation (PIV) supplies a controlled flow of filtered air, often from a loft-mounted unit or an internal unit, to create gentle positive pressure. Air leaves through natural leakage paths and existing vents. PIV can be a practical condensation solution in some homes, particularly where there is a loft and limited space for a complete ducted system, but it does not provide the same room-by-room extract and supply control as MVHR.

Extractor fans provide local mechanical extraction. Bathroom, kitchen and utility-room fans remove moisture and odours close to their source. They are usually less disruptive to install than a whole-house system, but they do not by themselves provide balanced ventilation throughout a property.

SystemBest suited toMain advantagesLimitationsInstallation and maintenance considerations
MVHRNew-builds, major refurbishments and relatively airtight homesBalanced whole-house airflow, filtration and potential heat recoveryRequires design, duct routes, space and careful commissioningHigher installation complexity; filters need regular inspection and replacement
PIVExisting homes with condensation concerns and suitable loft or internal spaceWhole-home background air supply with comparatively limited ductworkRelies on suitable air paths and may not remove moisture directly at sourceUnit and filters need checking; loft conditions and existing vents matter
Extractor fansBathrooms, kitchens, utility rooms and targeted moisture controlFocused extraction and usually simpler installationLocal rather than whole-house coverage; performance depends on airflow and useGrilles, filters, ducts and external terminals need cleaning and inspection

For a broader comparison of system choices, see MVHR vs PIV: Which Home Ventilation System Is Best for Your House?.

How to estimate the right option

Start with the problem rather than the product. Record which rooms show condensation, mould or persistent odours, when the symptoms appear and whether they coincide with bathing, cooking, drying clothes or cold weather. Also note whether windows have been replaced, whether the home has open chimneys or background vents, and whether the loft is suitable for equipment.

Then classify the project as one of three levels:

  1. Local intervention: one or more bathroom or kitchen extractor fans, improved controls, ducting or replacement external terminals.
  2. Whole-home supply: a PIV system where background air movement is needed and the building has appropriate escape routes for air.
  3. Whole-home balanced ventilation: an MVHR system where a major refurbishment or new-build allows ductwork, airtightness improvements and commissioning.

To compare quotes, calculate the total project cost rather than the equipment price alone. Add the unit, design, labour, electrical work, ductwork, roof or wall penetrations, access equipment, making good, commissioning, controls and any follow-up visit. Ask each installer to state clearly what is included and excluded.

For running costs, list the manufacturer’s stated electrical input, expected operating schedule and replacement filter requirements. Do not compare fan wattage alone: a system that is poorly sized, incorrectly commissioned or left running at an unsuitable setting may deliver disappointing results regardless of its advertised efficiency.

Inputs and assumptions for a quote comparison

Use the same information for every installer. This makes competing proposals easier to assess.

  • Property: house type, floor area, number of storeys, bedrooms and occupancy.
  • Construction: approximate age, insulation, window type, airtightness and any planned refurbishment.
  • Moisture sources: bathrooms, kitchen, utility room, indoor clothes drying and visible damp or mould.
  • Available routes: loft access, cupboards, service voids, ceiling space, external walls and roof terminals.
  • Controls: timers, humidity sensors, boost switches, continuous operation and user interfaces.
  • Sound: request the proposed sound levels in bedrooms and living spaces, not only the unit’s laboratory rating.
  • Maintenance: filter type, cleaning access, inspection frequency and likely replacement parts.
  • Compliance: ask how the design, installation and commissioning address the current requirements that apply to the project, including relevant ventilation guidance.

A credible quote should identify airflow calculations or design assumptions, the location of terminals and grilles, duct insulation where needed, commissioning measurements and handover instructions. Be cautious if a whole-house proposal contains no room-by-room airflow information or if an installer promises to cure damp without investigating other causes, such as leaks, failed gutters or penetrating moisture.

For practical checks before requesting a quote, use How to Test Ventilation Airflow at Home and the Home Ventilation Cost Guide UK.

Worked examples

Example 1: A flat with bathroom condensation. If the issue is concentrated in one bathroom, first compare the cost and disruption of a correctly ducted extractor fan with a whole-house system. Check that the fan can discharge effectively outdoors, that the duct is suitable and that the controls match how the room is used. A local solution may be more proportionate than installing PIV or MVHR.

Example 2: An older house with recurring window condensation. If several rooms are affected and the property has a suitable loft, compare a PIV quotation with a package of improved local extraction and background ventilation. Include checks for cold surfaces, blocked vents and moisture-producing habits. PIV may improve background air movement, but it should not be treated as a substitute for extracting steam at its source.

Example 3: A major renovation. If ceilings, floors or walls are already open, request an MVHR design alongside the refurbishment plans. Compare the additional ductwork and commissioning cost with the long-term benefits of balanced airflow, filtration and heat recovery. Confirm that the proposed airtightness strategy, room layout and maintenance access support the design.

In each example, record the quotation date, scope, warranty, expected maintenance and any assumptions about electrical tariffs or operating hours. This creates a useful baseline for future decisions without pretending that one national cost applies to every property.

When to recalculate

Revisit your comparison before accepting a quote if the property layout, window specification, insulation, airtightness or refurbishment scope changes. Recalculate when energy prices, equipment prices, labour rates or filter costs change, and whenever a manufacturer replaces a model or alters its maintenance requirements.

Review the relevant Building Regulations and ventilation guidance whenever the project changes from a simple replacement to a new installation, extension or major refurbishment. Requirements and local interpretations can change, so confirm the current position with a qualified designer, building control body or competent installer rather than relying on an old quotation.

After installation, review the system if condensation continues, rooms feel draughty, noise is intrusive or airflow seems weak. Ask for commissioning results and check that users understand boost settings, cleaning and filter replacement. The most useful next step is to create a three-column shortlist: suitable system, complete installed cost and ongoing obligations. Take that shortlist to at least two appropriately qualified installers and compare like for like.

Related Topics

#MVHR#PIV#extractor fans#ventilation comparison#home ventilation costs#buyer guide
A

Airvent Editorial Team

Home Ventilation Editors

Senior editor and content strategist. Writing about technology, design, and the future of digital media. Follow along for deep dives into the industry's moving parts.